As a time saver, can I premix my oils in the heater and use them up over a period of a week or more? Can the oils be reheated each day or continuously left at 110 degrees without unacceptable degradation of the oils?

Does the Oil-Wax Heater (Melter) maintain a constant temperature at the level required?

Printer-Friendly Version

Connect Your Melter

to Our Bottler!

Filling From Melter

Visit Bottler page...

13MH Water Jacketed Oil / Wax Tank (Melter) (Heater)

The Model 13MH Water Jacketed Oil / Wax Tanks (Melters) (Heaters) Come Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

$969.00

13MH220 Water Jacket Oil / Wax Tank (Melter) (Heater)

The Model 13MH220 Water Jacketed Oil / Wax Tanks (Melters) (Heaters) Come Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

Same as above , but with 220 volt plug

$969.00

Stainless Steel Production Tank (Heater) (Melter), with water jacket.

For Cold Processed; this unit can be used to heat just the base oils or to heat and mix the entire batch. Using to heat the oils only is the most efficient method.

For Melt and Pour it is perfect for heating large quantities and for dispensing into molds or other containers.

For Liquid Soap, this is the perfect vessel, total control for all steps….mixing, tracing, heat stage, dilution and bottling.

Candle Wax; this is great for melting wax, blending ingredients and dispensing into molds.

This unit can be attached directly to our EZ Fill Bottler.

Easy to use and maintain, just keep jacket full of water.

These versatile tanks are wonderful for Lip Balms, Body Butters, Massage Oils, Lotions, Creams,  virtually any product that requires even, controlled heat for blending.

Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve, Cord & Extra Element

We also provide an extra element with every tank. You may never need it but you will have it if you do.

All stainless steel construction.

Approximately 13 gal. (49L) capacity, 100 lbs (45.359Kg) in weight.

Exterior dimensions 21” (53cm) high by 18” (46cm) in diameter.

Interior dimensions approximately 15" x 16"

Flat bottom, Water boiler style, water jacket.

120 Volt, 1500 watt, Heater - Thermostat (50F to 250F) (10C to 121C).

	Note: For International customers with 220 volt 50 or 60 cycle we will substitute our 220 volt, 3000 watt, Heater - Thermostat. Domestic customers that wish to use 220 volt, we will change at no additional change.
	Your plug may need to be changed to conform with local or country codes.
	Current draw is, 12.5 amps at 120 volts

Includes extra element

Large, 1.5” (3.8cm) outlet.

Can ship via UPS. Weighs 45 lbs (20Kg), Oversize @ 70 lbs (32Kg).

Connect Your Melter

to Our Bottler!

Filling From Melter

Visit Bottler page...

45 Gallon (360 lbs) Water Jacketed Oil / Wax Tank (Melter) (Heater)

The Model 45MH Comes Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

(See Note below)

$1,335.00

Note:

Our Large Oil / Wax Tank (Melter) (Heater) require special shipping and therefore cannot be added to our cart, for Large Oil / Wax Tank (Melter) (Heater) orders, Please Click Here to Contact Us.

Stainless Steel Production Melter/Heater, with water jacket.

In producing soap this unit is best used with our Pot Tippers to heat the base oils.

Easy to use and maintain, just keep jacket full of water.

For Melt and Pour it is perfect for heating large quantities and for dispensing into molds or other containers.

For Liquid Soap, this is the perfect vessel, total control for all steps….mixing, tracing, heat stage, dilution and bottling.

Candle Wax; this is great for melting wax, blending ingredients and dispensing into molds.

These versatile tanks are wonderful for Lip Balms, Body Butters, Massage Oils, Lotions, Creams,  virtually any product that requires even, controlled heat for blending.

This unit can be attached directly to our EZ Fill Bottler.

Easy to use and maintain, just keep jacket full of water.

Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve, Cord & Extra Element

We also provide an extra element with every tank. You may never need it but you will have it if you do.

All stainless steel construction.

Approximately 45 gal (170L) capacity or approximately 360 lbs (163Kg).

Outside dim. are 29" (74cm) high by 26" (66cm) in diameter.

220 Volt, 3000 watt, Heater - Thermostat (50F to 250F) (10C to 121C). Draws about 14 amps, has a 6/30 style plug.

Uses a standard 6-30 NEMA rated plug.

Note: This unit is compatible for all International customers. The plug will have to be changed to conform with local codes.

Includes extra element

Flat bottom for easy cleaning.

Water jacketed, with a 1.5” (3.8cm) outlet.

Must be shipped Motor Freight. Crating is included in price.

Connect Your Melter

to Our Bottler!

Filling From Melter

Visit Bottler page...

60 Gallon (480 lbs) Water Jacketed Oil / Wax Tank (Melter) (Heater)

The Model 60MH Comes Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

(See Note below)

$1,675.00

Note:

Our Large Oil / Wax Tank (Melter) (Heater) require special shipping and therefore cannot be added to our cart, for Large Oil / Wax Melters orders, Contact Us.

Stainless Steel Production Melter/Heater, with water jacket.

In producing soap this unit is best used with our Pot Tippers to heat the base oils.

Easy to use and maintain, just keep jacket full of water.

For Melt and Pour it is perfect for heating large quantities and for dispensing into molds or other containers.

For Liquid Soap, this is the perfect vessel, total control for all steps….mixing, tracing, heat stage, dilution and bottling.

Candle Wax; this is great for melting wax, blending ingredients and dispensing into molds.

These versatile tanks are wonderful for Lip Balms, Body Butters, Massage Oils, Lotions, Creams,  virtually any product that requires even, controlled heat for blending.

This unit can be attached directly to our EZ Fill Bottler.

Easy to use and maintain, just keep jacket full of water.

Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve, Cord & Extra Element

We also provide an extra element with every tank. You may never need it but you will have it if you do.

All stainless steel construction.

Approximately 60 gal (227L) capacity or approximately 480 lbs (218Kg).

Outside dim. are 33" (84cm) high by 28" (71cm) in diameter.

220 Volt, 5000 watt, Heater - Thermostat (50F to 250F) (10C to 121C). Draws about 23 amps, has a 6/30 style plug.

Uses a standard 6-30 NEMA rated plug.

Note: This unit is compatible for all International customers. The plug will have to be changed to conform with local codes.

Includes extra element

Flat bottom for easy cleaning.

Water jacketed, with a 1.5” (3.8cm) outlet.

Must be shipped Motor Freight. Crating is included in price.

Connect Your Melter

to Our Bottler!

Filling From Melter

Visit Bottler page...

85 Gallon (680 lbs) Water Jacketed Oil / Wax Tank (Melter) (Heater)

10,000 watts - 2 each - 220 Volt, 5000 watt, Heater Units.

The Model 85MH Comes Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

** Non-Stock Item, Please allow 4-6 weeks for delivery.

(See Note below)

$2,385.00

Note:

Our Large Oil / Wax Tank (Melter) (Heater) require special shipping and therefore cannot be added to our cart, for Large Oil / Wax Melters orders, Contact Us.

Our largest Water Jacketed Oil / Wax Tank (Melter) (Heater)!

You can produce a lot of soap or candles easily and efficiently with this Water Jacketed Oil / Wax Tank (Melter) (Heater).

	Stainless Steel Production Melter/Heater, with water jacket.
	In producing soap this unit is best used with our Pot Tippers to heat the base oils.
	Easy to use and maintain, just keep jacket full of water.
	For Melt and Pour it is perfect for heating large quantities and for dispensing into molds or other containers.
	For Liquid Soap, this is the perfect vessel, total control for all steps….mixing, tracing, heat stage, dilution and bottling.
	Candle Wax; this is great for melting wax, blending ingredients and dispensing into molds.
	These versatile tanks are wonderful for Lip Balms, Body Butters, Massage Oils, Lotions, Creams,  virtually any product that requires even, controlled heat for blending.
	This unit can be attached directly to our EZ Fill Bottler.
	Easy to use and maintain, just keep jacket full of water.
	Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve, Cord & Extra Element
	We also provide an extra element with every tank. You may never need it but you will have it if you do.

Specifications:

	All stainless steel construction.
	Approximately 85 gal (321.76L) capacity or approximately 680 lbs (308Kg).
	Outside dim. are 37" (94cm) high by 31" (79cm) in diameter.
	10,000 watts - 2 each - 220 Volt, 5000 watt, Heater Units. Thermostats (50F to 250F) (10C to 121C). Each draws about 23 amps and has a, 6/30 style plug.

Note:: This unit is compatible for all International customers. The plug will have to be changed to conform with local codes.

	Includes extra element
	Flat bottom for easy cleaning.
	Water jacketed, with a 1.5” (3.8cm) outlet.
	Must be shipped Motor Freight. Crating is included in price.

Connect Your Melter

to Our Bottler!

Filling From Melter

Visit Bottler page...

125 Gallon (1,000 lbs) Water Jacketed Oil / Wax Tank (Melter) (Heater)

10,000 watts - 2 each - 220 Volt, 5000 watt, Heater Units.

The Model 125MH Comes Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve and Cord.

** Non-Stock Item, Please allow 4-6 weeks for delivery.

(See Note below)

$3,495.00

Note:

Our Large Oil / Wax Tank (Melter) (Heater) require special shipping and therefore cannot be added to our cart, for Large Oil / Wax Melters orders, Contact Us.

Our largest Water Jacketed Oil / Wax Tank (Melter) (Heater)!

You can produce a lot of soap or candles easily and efficiently with this Water Jacketed Oil / Wax Tank (Melter) (Heater).

	Stainless Steel Production Melter/Heater, with water jacket.
	In producing soap this unit is best used with our Pot Tippers to heat the base oils.
	Easy to use and maintain, just keep jacket full of water.
	For Melt and Pour it is perfect for heating large quantities and for dispensing into molds or other containers.
	For Liquid Soap, this is the perfect vessel, total control for all steps….mixing, tracing, heat stage, dilution and bottling.
	Candle Wax; this is great for melting wax, blending ingredients and dispensing into molds.
	These versatile tanks are wonderful for Lip Balms, Body Butters, Massage Oils, Lotions, Creams,  virtually any product that requires even, controlled heat for blending.
	This unit can be attached directly to our EZ Fill Bottler.
	Easy to use and maintain, just keep jacket full of water.
	Complete with: Lid, Heater - Thermostat, 1.5 Inch Ball Valve, Cord & Extra Element
	We also provide an extra element with every tank. You may never need it but you will have it if you do.

Specifications:

	All stainless steel construction.
	Approximately 125 gal (473.17L) capacity or approximately 1,000 lbs (454Kg).
	10,000 watts - 2 each - 220 Volt, 5000 watt, Heater Units. Thermostats (50F to 250F) (10C to 121C). Each draws about 23 amps and has a, 6/30 style plug.

Note:: This unit is compatible for all International customers. The plug will have to be changed to conform with local codes.

	Includes extra element
	Flat bottom for easy cleaning.
	Water jacketed, with a 1.5” (3.8cm) outlet.
	Must be shipped Motor Freight. Crating is included in price.

Click Image to Enlarge

Oil / Wax Tank (Melter) (Heater) Jacket

Save Money and Save Time! By covering your tanks with an insulation jacket, you will cut your energy usage drastically. And…you will save time because your materials will heat faster and stay heated longer.

Description:

	Your Oil-Wax Melter Jacket is made with a tough, heat resistant foam core and heavy foil lining, inside and out.
	This is a high R-value, highly reflective and extremely efficient material, which will effectively conserve heat and energy, saving you money.
	Your Jacket kit is pre-cut, top, bottom and side panel. In about ten minutes you can have your jacket fitted, taped and ready to go.
	You kit includes plenty of heavy duty, reflective, foil tape and instructions. All you need is a sharp knife or box cutting knife.
	Water, oils and heat will not affect its insulation value.

Specifications:

	Made of ¼” (7mm), High R, Foam Core, Double Sided, Foil Faced, insulation.
	Heavy duty foil tape included.
	Can be shipped UPS

PLEASE NOTE:

If you purchased a tank from us, prior to 3/1/09, you will have a slightly different style of tank. We changed sizes.

	15 gallon Oil / Wax Tank (Melter) (Heater) - Use 13MHJ pricing.
	35 gallon Oil / Wax Tank (Melter) (Heater) - Use 45MHJ pricing.
	65 gallon Oil / Wax Tank (Melter) (Heater) - Use 60MHJ pricing.

Please include a note in the “Comment Section” of your order as to what size you have. Your jacket/s will be made to fit your tank.

13MHJ

13 gallon Oil-Wax Melter Jacket

NOTE: Owners of our 15 Gallon Melters Order this model.

$33.00

45MHJ

45 gallon Oil-Wax Melter Jacket

NOTE: Owners of our 35 Gallon Melters Order this model.

$47.00

60MHJ

60 gallon Oil-Wax Melter Jacket

NOTE: Owners of our 65 Gallon Melters Order this model.

$60.00

85MHJ

85 gallon Oil-Wax Melter Jacket

$67.00

Oil/Wax Tank (Melter) (Heater) Slow Speed Mixer

Here is the Perfect Solution for continuous mixing of any solution, from watery liquids to thick creams, from ice cold milk to the hottest candle wax. If you need something special just ask.

Description:

The Double Blade System is perfect for incorporating liquids, herbs, or solids into the mix. No worries, mixing air into your formula, gentle yet thorough.

	This mixer is geared to have incredible torque and power. Thick slurries such as lotions, creams, etc. are no problem.
	The Slow Speed Mixer, is ideal for thick creams, lotions, butters, beeswax, even fist sized chunks of M&P, oils, fragrances, essential oils, or wax. Please note: some of the wax or M&P must be liquid so the blades don't jam and can turn freely.
	The Impeller Blades are polypropylene, 3" (7.62") wide, angled at 30 degrees.
	The impeller blades are 22" (56cm) tip to tip.
	The Shaft is milled 6" (15cm) in length at the center point, to allow blade adjustment, up or down.
	All fittings and shaft are Stainless Steel.
	All parts including the motor channel, mount are made of Food Grade Materials.
	All parts are rated to 230 F (210C). The whole assembly weighs only, 15 pounds (6kg), making it very easy to lift out of the tank.
	The lid is now hinged at one side (not shown) so you simply lift the lid, to add ingredients or look in. The other side of the lid, slips over the motor channel, mount and is easily and quickly removed for full access.
	There is Zero maintenance.

Specifications:

	Operates on 120 volt current, drawing less than 2 amps.
	The motor is designed for continuous duty. Motor is fully enclosed and moisture resistant.
	The 8' (2.4m) cord is oil and chemical resistant.
	Can be shipped UPS.
	Special motor speeds are available up to 250 rpm. Call for Pricing.

OHM1-13

Oil/Wax Melter Slow Speed Mixer

Single Blade for 13 Gallon Oil/Wax Melter

$595.00

OHM2-45

Oil/Wax Melter Slow Speed Mixer

Double Blade for 45 Gallon Oil/Wax Melter

NOTE: Owners of our 35 Gallon Melters Order this model.

$728.00

OHM2-60

Oil/Wax Melter Slow Speed Mixer

Double Blade for 60 Gallon Oil/Wax Melter

NOTE: Owners of our 65 Gallon Melters Order this model.

$828.00

OHM2-85

Oil/Wax Melter Slow Speed Mixer

Double Blade for 85 Gallon Oil/Wax Melter

$928.00

OHM2-125

Oil/Wax Melter Slow Speed Mixer

Double Blade for 125 Gallon Oil/Wax Melter

$1,195.00

Note:

Owners of our 65 Gallon and 35 Gallon Oil/Wax Melters can order these Great Slow Speed Mixers, SEE NOTES ABOVE. If you have questions: Please Contact Us.

1.5 Inch Replacement Ball Valve

for our Oil / Wax Tank (Melter) (Heater)

Three way, polypropylene ball valve. Impervious to sodium or potassium hydroxide. Liquid can flow either horizontally or vertically. Comes set up for 90 degree, down dispensing.

Note:

For those not familiar with the term Ball Valve this is a valve, faucet or means of controlling the flow of liquid. A quick 1/4 turn and all flow of liquid can be shut off. This particular valve allows liquid to quickly flow from a horizontal path to a vertical path for dispensing into vessels or into individual molds. We can supply as an option, reduction fittings for small cavity molds.

Also, see our Reducer for the Ball Valve  > > > > > > >

Reducer for Oil Heater

Picture of how the

Reducer would attach

to the Ball Valve

Instructions

Reducer for Oil - Wax Tank (Melter) (Heater)

for our 1.5 inch Ball Valve

This reducer is great for filling bottles, candle molds, M&P molds, etc. right from the Oil / Wax Tank (Melter) (Heater).

Description:

	For those just getting into filling bottles and not quite ready for our Easy Fill Bottler, this is a great way to start.
	For Candles or M&P (Glycerin Soap) this will save considerable time on filling molds or small cavity soap molds.
	This is much more efficient than pouring into a container and then into a bottle or mold.
	Fits right into our 1 1/2" (38mm) Ball Valve and allows you to turn the 1 1/2" valve fully on and adjust fluid flow or cut the flow on and off, with the smaller 1/2" (13mm) Ball Valve.

Specifications:

	Reduction from 1 1/2" (38mm) Ball Valve to a 3/8" (10mm)flow.
	Fully assembled, no pipe cement or teflon tape needed to attach to 1 1/2" (38mm) Ball Valve.
	Will handle temps up to 220 F (104 C).
	Will handle most acids and alkalis.

Instructions for using Ball Valve Reducer:

	Thread the reducer into the ball valve, hand tight, so it is easy to remove. Plastic to plastic makes a good seal and does not need to be extremely tight.
	Make sure the reducer valve is closed.
	Open the big ball valve and then start dispensing, using the small ball valve on the reducer.
	When you are done, close the big valve and unscrew the reducer.
	Open the small valve and run a dowel rod or twist up a piece of rag and run through it to clean most of the wax, lotion, etc. Wash, and you are ready for the next batch.

HANDcraft™ Brass Ball Valve

Brass Ball Valve 3/4"

HANDcraft™

Heated Ball Valve

Assembly

HANDcraft™ Heated Valve Assembly

This is perfect for companies who pour a lot of Candle Wax, M&P or Liquids requiring constant heat from tank to mold.

	Easy to remove and replace with our standard 3 way Ball Valve for different operations.
	Works with All of our Oil/ Wax Melters.
	Preassembled and ready to be installed on your Oil / Wax Melters.
	Easy to remove and replace with our standard 3 way Ball Valve for different operations.
	Plug in the HANDcraft™ Ball Valve Heater and you are ready to pour.
	Includes 1 ½” Poly Coupling w/ ¾” Brass Ball Valve and 90 degree brass elbow, HANDcraft™ Ball Valve Heater, Foam Insulation for the Poly Coupling.

HANDcraft™ Ball Valve Heater

Never have your wax set up in your Ball Valve again with our HANDcraft™ Ball Valve Band Heater .

45W 120V band heater complete with Velcro strips that fit perfectly around 3/4" or 1" Metal Ball Valves.

Note:

Not for use with Plastic Ball Valves

HANDcraft™ Heater Timer 1800 watt

What a great way to have time work for you. Simply set the timer for when you want your Heater or appliance to turn on and walk away.

Have it turn your Drum or Bucket Heater on in the early morning hours so your oils are ready for the work day.

Description:

	You can use this 1800 watt Timer on any of our 110/120 volt pieces of equipment such as; 15 gallon Oil Heater, Drum Heater, Bucket Heater and 45 gallon NaOH Tank.
	4 ON / 4 OFF settings per day. A total of 56 ON / 56 OFF settings per week.
	Can be used with 4 separate programming options: Same settings Monday through Friday, Same settings Saturday and Sunday, Same settings all 7 days of the week, Various daily settings.
	Two Timed, Grounded Outlets.
	Has a cover to protect against dust and moisture.

Specifications:

	Two replaceable LR44, button cell batteries (included) maintains program during power failure and will keep time up to 3 months.
	Low battery indicator
	Time of Day display. Automatically adjusts for Daylight Savings Time.
	Easy hand-held programming
	120 Volts, 60 Hz, 18 inch cord.
	15 Amps, handles up to 1800 watts.
	2 year manufacturer warranty

HANDcraft™ Heater Timer 7200 watt

Have time work for you and save energy. Just set the timer and your oils will be heated and ready for you the next work day.

Description:

	Save energy; no need to leave your Oil / Wax Tank (Melter) (Heater) on all night.
	Save time; why waste part of your day waiting for the oils to heat up? Also works with our 80 gallon Lye Tank.
	Dependable and Easy to use, comes with battery back up.
	Up to 8 set points, 4 ON / 4 OFF, can be programmed daily.
	Can be manually overridden at any time.
	Has a lockable cover to protect against dust and moisture.

Specifications:

	Water pole switching
	120 thru 277 volt input
	30 Amps/pole
	3 year user replaceable battery back up
	Steel enclosure

Replacement Parts for Oil / Wax Heaters (Melters)

Replacement Oil - Wax Tank (Melter) (Heater) Lids

Replacement 220 volt / 3000 watt heater / thermostat

For use with the 45MH & 60MH Oil / Wax Tank (Melter) (Heater).

Best used with our 45MH Oil / Wax Tank (Melter) (Heater), but will also work with our 60MH Oil / Wax Tank (Melter) (Heater).

Replacement 110 volt / 1500 watt heater / thermostat

Replacement 220 volt / 5000 watt heater / thermostat

Designed for use with our 13MH and 45MH Oil / Wax Tank (Melter) (Heater).

Best used for our 60MH Oil / Wax Tank (Melter) (Heater).